Pilling Group Mazda

Subject = Pilling group Mazda
Description = Pilling group mazda
Category = Pilling Mazda

Mazda

rotary engine

rotary engine

rotary engine

Mazda

cars

cars

cars

Over the years, displacement has been increased (somewhat) mazda motors , and turbocharging has been added to great effect

Mazda

cars

cars

cars

This is the engine family that made

Mazda

Mazda

cars

cars

cars

In

auto racing

Mazda

cars

cars

cars

So the 1.3 L 13B engines count as just under 2.0 L for these purposes

Mazda

cars

cars

cars

rotary engine

Mazda

cars

cars

cars

These metrics function similarly to the bore and stroke measurements of a piston engine

Mazda

cars

cars

cars

mazda motors Nearly all

Mazda

rotary engine

Mazda

cars

cars

cars

The only engine to diverge from this formula mazda motors was the rare 13A, which used a 120 mm (4.7 in) diameter and 17.5 mm (0.7 in) offset

Mazda

cars

cars

cars

40A

Mazda

rotary engine

Mazda

cars

cars

cars

Although never produced in volume, the 40A was a valuable testbed for

Mazda

Mazda

cars

cars

cars

The chatter marks, nicknamed devil's fingernails, were caused by improper sealing at the apex of the rotor

Mazda

cars

cars

cars

The oil consumption problem was mazda motors addressed with heat-resistant rubber oil seals at the sides of the rotors

Mazda

cars

cars

cars

This early engine had a rotor diameter of 90 mm (3.5 in) , an offset of 14 mm (0.6 in) mazda motors , and a depth of 59 mm (2.3 in)

Mazda

cars

cars

cars

L8A

The very first

Mazda

rotary engine

Mazda

cars

cars

cars

The engine and car mazda motors were both shown at the 1963 Tokyo Motor Show

Mazda

cars

cars

cars

Hollow cast iron apex seals reduced vibration and thus chatter marks

Mazda

cars

cars

cars

It used dry-sump lubrication

Mazda

cars

cars

cars

Rotor diameter was up from the mazda motors 40A to 98 mm (3.9 in) , but depth dropped to 56 mm (2.2 in)

Mazda

cars

cars

cars

One-, three-, and four-rotor derivatives of the L8A were also created for experimentation

Mazda

cars

cars

cars

mazda motors 10A

The 10A series was

Mazda

rotary engine

Mazda

cars

cars

cars

It was a two-rotor design, with each displacing 491 cc for a total of 982 cc

Mazda

cars

cars

cars

These mazda motors engine featured the mainstream rotor dimensions with a 60 mm (2.4 in) depth

Mazda

cars

cars

cars

The rotor housing was made of sand-cast aluminum plated with chrome, while the aluminum sides were sprayed with mazda motors molten carbon steel for strength

Mazda

cars

cars

cars

Cast iron was used for the rotors themselves, and their eccentric shafts were of expensive chrome-molybdenum steel

Mazda

cars

cars

cars

The addition of aluminum/carbon apex seals addressed the chatter mazda motors mark problem

Mazda

cars

cars

cars

0810

The first 10A engine was the 0810, used in the Series I Cosmo from May, 1965 through July, 1968

Mazda

cars

cars

cars

These

cars

Mazda

cars

cars

cars

Gross output was 110 hp (82 kW) at 7000 RPM and 130 Nm (96 ft.lbf) at 3500 RPM, but both numbers were probably optimistic

Mazda

cars

cars

cars

The 10A mazda motors featured twin side intake ports per rotor, each fed by a one of four carburetor barrels

Mazda

cars

cars

cars

Only one port per rotor was used under low loads for added fuel economy

Mazda

cars

cars

cars

A mazda motors single peripheral exhaust port routed hot gas through the coolest parts of the housing, and engine coolant flowed axially rather than the radial flow used by NSU

Mazda

cars

cars

cars

A bit of oil was mazda motors mixed with the intake charge for lubrication

Mazda

cars

cars

cars

The 0810 was modified for the racing Cosmos used at Nürburgring

Mazda

cars

cars

cars

These engines had both side- and peripheral-located intake ports switched with a mazda motors butterfly valve for low- and high-RPM use (respectively)

Mazda

cars

cars

cars